Torso support OT-05

Product description

It is made of airy materials what allows sweat to evaporate from the skin. Anatomic shape provides good device fitting and better TLSO stabilization. Additional asset is the height adjustment of the chassis. Thanks to under armpit straps allow to achieve full anterior-posterior stabilization. The rear part of the brace is made of ActivSpace material, which is non-elastic what increases the spine stabilization. Thickness and toughness of the material is well-suited to the patient’s spine anatomy.

Lateral parts of the brace are made of perforated orthopaedic foam, which has only one-direction elasticity. The little wholes allow skin to breath.

The rear part of the OT-05, depends on the size, is equipped with 2 or 4 orthopaedic whalebones and high aluminium spine splints.

The orthopaedic splints are anatomically shaped and hold sweat-resistant coating. The brace’s fastenings are asymmetric. This solution allow to fit device to the body precisely. Two sets of 3 straps provide better thoracolumbar spine stabilization.

Indications

OT-05 should be applied in case of:

• severe L-S painful syndrome
• multilevel Degenerative Disc Disease
• multilevel discopathy
• osteoporosis
• spine instability
• lumbar spondylolisthesis
• Spinal Compression Fractures
• sciatica
• after surgeries (orthopaedics, neurology)

Available sizes

Size	Waist circumference	How to measure
S	65 – 75 cm (22,6″-29,5″)
M	75 – 85 cm (29,5″-33,5″)
L	85 – 97 cm (33,5″-38,2″)
XL	97 – 110 cm (38,2″-43,3″)
2XL	110 – 125 cm (43,3″-49,2″)
3XL	125 – 145 cm (49,2″-57,1″)

Size	Height (A)	How to measure
S	43 cm (16,9″)
M	46 cm (18,1″)
L	49 cm (19,3″)
XL	52 cm (20,5″)
XXL	55 cm (21,7″)
XXXL	55 cm (21,7″)

MATERIALS

ActivePren™

ActivePren™ is an active three-layer material consisting of two elastic jersey cover fabrics and a core made of neoprene foam. This material is characterized by softness and high flexibility. A very important advantage of this material is the fact that it is not a knitted product, it does not have thick fibers, so that the weaves of the material do not imprint on the patient's skin and do not cause abrasionsin places of high compression. Products made of ActivePren are the strongest and most effective stabilizing orthoses available on the market.

AirRubber™

AirRubber™ has unidirectional elasticity and it’s breathable. This lamination is perforated. Between the braids air flows freely and skin can breathe. In addition in high compression, these rubber braids provide a gentle massage for skin. Our orthopedic rubber is very friendly for skin.

STIFFENINGS

Plastic stays

They come in various widths and thicknesses, are made of various types of plastics, such as polyamide, ABS or acrylic, and these features determine their stiffness. Thanks to their design, they are resistant to water, moisture and sweat. Products equipped with them can be washed without having to remove them from the orthosis. Our plastic stays work only in one direction, perfectly stabilize the laterally protected part of the body, adjusting to it at the same time and have a memory function, thanks to which they always return to their original shape. This function causes the stays in the orthosis to stabilize the swollen limb immediately after the injury and after the swelling has come off. The plastic stays cannot bend and that is why, they cannot correct the body posture or the secured joint.

• Declaration of Conformity EC
• Manual
• Manual (other languages)
• Setting up