Lower limb support AM-OSK-OL/1R-01
Knee brace
Breathable
Class I medical device
Cotton
Double-sided
Innovative
Latex-free
Magnetic joint 1R orthodesign
Recommended by specialists
Skin-friendlyWRAP AROUND LOWER LIMB BRACE WITH 15° ROM ADJUSTMENT
Description
6 POINT BRACES
The braces are intended for long-time using in patients with complicated knee instability (partly or complete ACL rupture), which is result of early injuries (before or postoperative) or after joint conditions.
Anatomic profiled splints increase the control of knee movement and provide additionally support points in hinges of the brace (5 and 6 point) by using sides pellotes. It increases control of movement in frontal and rotation plate. The anatomic fitting the brace to the limb is supported by anatomic drop lock.
The AM-OSK-OL/1R-01 brace provides excellent knee stabilization, including frontal and sagittal plate and control of rotation movement, what allows to replace partly injured ligaments and articular capsule. The high level of stabilization allows for competitive training (especially in skiing) or allows for taking part in sport and other activities even in senior age.
The brace is made of ProSIX II™, AeroSpace™
The device is equipped with two independent support straps made of VELCRO tapes and two 2-axial sides splints 1R orthodesign.
Purpose of use
Wrap-around lower limb brace with 15o ROM adjustment should be applied in cases of:
– knee dislocation,
– knee twist and sprain,
– side instability of the knee joint,
– knee ligaments LCL, MCL and ACL injuries
– knee ligaments reconstruction
– other surgeries (orthopedic),
Sizes
| Size | (A) Thigh circumference 15 cm above the center of the patella | (B) Calf circumference 15 cm below the center of the patella | How to measure |
| S | 40-44 cm (15,7″-17,3″) |
30-34 cm (11,8″-13,4″) |
 |
| M | 44-48 cm (17,5″-18,9″) |
34-38 cm (13,6″-15″) |
|
| L | 48-52 cm (19″-20,5″) |
38-42 cm (15,2″-16,5″) |
|
| XL | 52-56 cm (20,7″-22″) |
42-46 cm (16,7″-18,1″) |
|
| XXL | 56-60 cm (22,2″-23,6″) |
46-50 cm (18,3″-19,7″) |
|
| XXXL | 60-64 cm (23,8″-25,1″) |
50-54 cm (19,9″-21,3″) |
Total length of product: 45 cm (17,7″)
Gallery
Click on the photo to enlarge
Technology
MATERIALS
ActivePren™
ActivePren™ is an active three-layer material consisting of two elastic jersey cover fabrics and a core made of neoprene foam. This material is characterized by softness and high flexibility. A very important advantage of this material is the fact that it is not a knitted product, it does not have thick fibers, so that the weaves of the material do not imprint on the patient's skin and do not cause abrasionsin places of high compression. Products made of ActivePren are the strongest and most effective stabilizing orthoses available on the market.
ProSix™
ProSix™ is an innovative fabric 3D, elastic in all directions and fitting to the limb precisely. The external layer is 3D material providing excellent stabilization. There is duothermic spacer foam providing high air permeability and compression inside. The skin has contact with cotton that is breathable and soft. ProSix™ is friendly and neutral for the skin and has Oeko-Tex Standard 100 certificate.
TECHNOLOGICAL SYSTEMS
STIFFENINGS
Splint 1R Orthodesign
The 1R orthodesign orthopedic splint is a novel approach to the subject of orthopedic splints with flexion and extension angle adjustment. The innovativeness of the splint lies in the fact that in a hinge dial with a diameter not exceeding 30 mm, we have applied flexion and extension angle adjustment every 15 degrees. An additional advantage of the splint is that the adjustment is not done using Allen screws, as was the case in the previous generation of the splint, but by means of inserted steel pins, which, for convenience, are removed from the angle sockets using a magnet included with the splints. The icing on the cake is the locking ring, which, thanks to a ratchet system, will not allow the previously set angle to change spontaneously. In knee braces, the splints have a tibial offset, which allows for a more precise fit of the knee brace, and consequently, they more accurately execute the regulation of joint mobility, while in other products, the braces have a straight form. On the underside of the hinge dial, an oval element is mounted to which a gripper is glued, necessary for attaching soft 3D side pads to the dial. These splints, using an orthopedic wrench available in the Reh4Mat offer, can in some cases be individually adapted to the shape of the patient's limb by bending them slightly. Download the adjustment instructions for the 1R orthodesign splint
Setting up
Downloads
Accessories
ON OUR WEBSITE WE PRESENT MEDICAL DEVICES.
USE THEM ACCORDING TO THE INSTRUCTIONS FOR USE OR LABEL.
Class I medical device in accordance with Regulation (EU) 2017/745 of the European Parliament and of the Council of 5 April 2017. on medical devices.
MANUFACTURER / ADVERTISING ENTITY: REH4MAT Sp. z o.o.
